in bend造句

• The road started to turn in bends and switchback .
  公路变成了那种“之”字形的盘山路。
• Method of testing in bending strength of wood
  木材抗弯强度试验方法
• A general solution of anisotropic thin plate in bending problem
  各向异性矩形薄板弯曲问题的一般解
• Test method for modulus of rupture in bending of electrode graphite
  石墨电极芯挠曲断裂模数的试验方法
• A general analytical solution of anisotropic rectangular plates in bending
  各向异性矩形板弯曲的一般解析解
• The general for determining deflections of the stepped beams in bending
  阶梯梁弯曲变形的普遍表达式及其应用
• Wood-based panels-determination of modulus of elasticity in bending and of bending strength
  木基板.弯曲弹性模量和弯曲强度的测定
• Wood-based panels . determination of modulus of elasticity in bending and of bending strength
  木基板.弯曲和弯曲强度时弹性模量的测定
• Under the excitation of wind forces, a building vibrates in bended and torsional modes
  在风力作用下,高层建筑将发生弯曲和扭转模态下的振动。
• And tendons remain in bent position for 15 seconds each time . repeat complete cycle of movements five times
  每次停15秒，来回算1次，共做5次。
• Evaluation on minimum amount of reinforcing steel in bent component of reinforced concrete box girder
  钢筋混凝土箱形截面受弯构件最小配筋量的计算
• Wood-based panels; determination of modulus of elasticity in bending and of bending strength; german version en 310 : 1993
  木基板材.弯曲弹性模量和弯曲强度测定
• The theoretical calculating method is useful to research farther the spring back of tailor welded blanks in bending process
  所得理论计算模型对研究差厚拼焊板的弯曲回弹及模具设计具有指导意义。
• Testing of plastics films and coated textile fabrics, manufactured using plastics; determination of stiffness in bending, method according to ohlsen
  用塑料制造的塑料薄膜和涂层的纺织织物的检验.用ohls
• Springback is a common phenomenon in bending process, which is caused by the redistribution of the internal stresses during unloading
  回弹是弯曲成形中普遍存在的现象，是由卸载过程中内力重新分布引起的。
• She stood up from her stool and worked that way for a while, but it was a more difficult position . her neck and shoulders ached in bending over
  但站着干更累人，她得弯着腰，于是她的头颈和肩膀都疼了起来。
• Testing of plastics films and textile fabrics excluding nonwovens, coated or not coated fabrics-determination of stiffness in bending-method according to cantilever
  带或不带涂层织物的塑料薄膜和纺织物
• A general solution of partial differential equation for transverse displacement function of anisotropic rectangular plates in bending was established in this paper
  摘要建立了各向异性矩形板弯曲的横向位移函数偏微分方程的一般解。
• The ball gets some of this lost energy ( the same for all racquets under all benchmark conditions ), and the rest becomes internal energy, wasted in bending the frame
  球拍所释放的能量一部分转换为球的动能，另一部分还可以转变为内能，消耗在球拍弯曲的过程中。
• Therefore, the research in bending problem of moderate-thick plates and the analysis in the interactions of plates and foundation becomes more important in engineering practice
  因此,中厚度弹性地基板的弯曲问题研究以及板与地基相互作用分析对工程实践有着越来越重要的意义。